10/23/2023 0 Comments Creative grids flying geese ruler![]() Problem solved quickly, easily and without much hullabaloo! Those two tiny triangles by the scissors created by trimming are scraps The photo below is a bit fuzzy due to the closeness of the patch, but I think it's easier for you to see the extra layers. Unfortunately, when you add the third and fourth squares, two extra layers of fabric are trapped/sewn-into the point of your FG unit. The first two squares overlap a fair amount-remember they were cut generously. (To be honest, I've not seen it mentioned in any of the instructions I've ever seen for No Waste or 4-at-a-Time Flying Geese either. This little trick isn't mentioned on the Wing Clipper ruler's instruction sheet-but it solves a problem with construction. Note: If you've jumped to this page from the 'Perfect No Waste Flying Geese Quilt Blocks tutorial, you'll find a link at the end of this trick to get you right back to where you left off. Visit my No Waste FG tutorial to download your own copy of my personal cutting chart. However, when I cut patches for my own use, I cut the four 'Sky' squares 1/4" larger because I can avoid 'scooching those patches in a smidgen' from the edge.Ī slight variation from the designer's method-but it works better for me. It's what I used for cutting my patches in the tutorial above so that you could see how they work. There is a cutting chart included in the package with the ruler when you get it. Many quilters have good results using Mary Ellen's Best Press (which is a sizing, not a starch), too. I do avoid spraying the mixture on my Magic Pressing Mat to take care of it. Water because I can control the stiffness. My go-to is a mix of 50/50 StaFlo liquid fabric starch concentrate to I love working with starched quilt fabric.īecause the fibers don't shift while you're cutting and piecing, the final patchwork is just plain more accurate. With your rotary cutter, trim the right and top sides. Now line up the "V" lines with the seam lines of your FG (red arrows below). ![]() Place the ruler on top with the 10-1/2" side furthest away from you (wide side of the FG) the 5-1/2" side in on the right.įor our 2" x 3½" unfinished (1½" x 3" finished) sample, the 2" and 3-1/2" lines of the ruler should be just a bit in from the cut edge of the unit on the left and bottom edge. (Remember, complete instructions are included with the ruler for left-handers.) The Wing Clipper Ruler is a trim down ruler-meaning that it's used to trim oversized units to perfection without a lot of futzing around.Īnd it is a thing of beauty.perfectly engineered.įor right-handers, position a Flying Geese unit on your cutting mat with the point towards your belly. Now it's time to reveal the 'magic' of the Wing Clipper ruler-it's all in the lines. The only difference is the smaller squares about scooched a scant 1/16" in from the edges. Up to this point, making Flying Geese 4-at-a-time is just like the No Waste Flying Geese method shown on this website. We're ready to trim them to perfection with our Wing Clipper Ruler. With a Quick Quarter ruler (shown here) or a standard quilting ruler, drawn two continuous lines, each a quarter inch away from the center diagonal. The smaller squares are placed a scant 1/16" (a smidgen) in from each pair of adjacent outside edges. With RST layer the larger Goose square with two smaller 'Sky' squares in opposite diagonal corners on top. I share those tips lower down on this page. What follows is construction of the four identical units as per the instruction sheet that comes with your Wing Clipper ruler.Īfter working with this ruler for awhile, I've made a couple of modifications to the process to suit the way I prefer to work. Pressing instructions are highlighted in yellow. Then press the SA away from the Goose making sure there is no tuck in at the seam allowance. These abbreviations are used in this tutorial:įor the best results, stitched units should be pressed, first flat to set the seam and meld the fibers of the thread with the fibers of the fabric. For our sample those cutting dimensions are: Use the cutting chart that comes with the ruler to cut one 'Goose' and four 'Sky' squares. ![]() In this tutorial we make four 1½"x3" finished (2"x3½" unfinished) Flying Geese units.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |